View H3LIS331DL_7465711.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

this is information on a product in full production. july 2013 docid023111 rev 2 1/38 H3LIS331DL mems motion sensor: low-power high-g 3-axis digital accelerometer datasheet - production data features ? wide supply voltage, 2.16 v to 3.6 v ? low-voltage compatible ios, 1.8 v ? ultra-low power consumption down to 10 a in low-power mode ? 100 g /200 g /400 g dynamically selectable full scales ? i 2 c/spi digital output interface ? 16-bit data output ? sleep-to-wakeup function ? 10000 g high-shock survivability ? ecopack ? , rohs and ?green? compliant applications ? shock detection ? impact recognition and logging ? concussion detection description the H3LIS331DL is a low-power high- performance 3-axis linear accelerometer belonging to the ?nano? family, with digital i 2 c/spi serial interface standard output. the device features ultra-low power operational modes that allow advanced power saving and smart sleep-to-wakeup functions. the H3LIS331DL has dynamically user- selectable full scales of 100 g /200 g /400 g and it is capable of measuring accelerations with output data rates from 0.5 hz to 1 khz. the H3LIS331DL is available in a small thin plastic land grid array package (lga) and it is guaranteed to operate over an extended temperature range from -40 c to +85 c. tflga 3x3x1.0 mm 3 16l table 1. device summary order codes temperature range [ ? c] package packaging H3LIS331DL -40 to +85 tflga 3x3x1.0 mm 3 16l tray H3LIS331DLtr -40 to +85 tflga 3x3x1.0 mm 3 16l tape and reel www.st.com
contents H3LIS331DL 2/38 docid023111 rev 2 contents 1 block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.1 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 mechanical and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . 9 2.1 mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.2 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.3 communication interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.3.1 spi - serial peripheral interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.3.2 i 2 c - inter-ic control interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.4 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.5 terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.5.1 sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.5.2 zero-g level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.5.3 sleep-to-wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3 functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.1 sensing element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.2 ic interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.3 factory calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4 application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.1 soldering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5 digital interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.1 i 2 c serial interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.1.1 i 2 c operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.2 spi bus interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.2.1 spi read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.2.2 spi write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.2.3 spi read in 3-wire mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6 register mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
docid023111 rev 2 3/38 H3LIS331DL contents 38 7 register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.1 who_am_i (0fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.2 ctrl_reg1 (20h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.3 ctrl_reg2 (21h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.4 ctrl_reg3 [interrupt ctrl register] (22h) . . . . . . . . . . . . . . . . . . . . . . 27 7.5 ctrl_reg4 (23h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.6 ctrl_reg5 (24h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7.7 hp_filter_reset (25h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.8 reference (26h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.9 status_reg (27h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.10 out_x_l (28h), out_x_h (29h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.11 out_y_l (2ah), out_y_h (2bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.12 out_z_l (2ch), out_z_h (2dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.13 int1_cfg (30h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.14 int1_src (31h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 7.15 int1_ths (32h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.16 int1_duration (33h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.17 int2_cfg (34h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.18 int2_src (35h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.19 int2_ths (36h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7.20 int2_duration (37h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
list of tables H3LIS331DL 4/38 docid023111 rev 2 list of tables table 1. device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table 2. pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 3. mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 table 4. electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 5. spi slave timing values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 6. i 2 c slave timing values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 7. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 8. serial interface pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 9. serial interface pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 10. sad+read/write patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 11. transfer when master is writing one byte to slave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 12. transfer when master is writing multiple bytes to slave . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 13. transfer when master is receiving (reading) one byte of data from slave . . . . . . . . . . . . . 19 table 14. transfer when master is receiving (reading) multiple bytes of data from slave . . . . . . . . . 19 table 15. register address map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 table 16. who_am_i register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 table 17. ctrl_reg1 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 table 18. ctrl_reg1 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 table 19. power mode and low-power output data rate configurations . . . . . . . . . . . . . . . . . . . . . . . 25 table 20. normal mode output data rate configurations and low-pass cutoff frequencies . . . . . . . . . 25 table 21. ctrl_reg2 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 table 22. ctrl_reg2 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 table 23. high-pass filter mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 table 24. high-pass filter cutoff frequency configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 table 25. ctrl_reg3 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 26. ctrl_reg3 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 27. data signal on int 1 and int 2 pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 table 28. ctrl_reg4 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 29. ctrl_reg4 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 30. ctrl_reg5 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 31. ctrl_reg5 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 32. sleep-to-wake configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 33. reference register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 34. reference description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 table 35. status_reg register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 36. status_reg description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 table 37. int1_cfg register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 38. int1_cfg description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 39. interrupt 1 source configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 40. int1_src register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 41. int1_src description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 42. int1_ths register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 table 43. int1_ths description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 table 44. int1_duration register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 table 45. int2_duration description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 table 46. int2_cfg register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 table 47. int2_cfg description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 table 48. interrupt mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
docid023111 rev 2 5/38 H3LIS331DL list of tables 38 table 49. int2_src register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 table 50. int2_src description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 table 51. int2_ths register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 table 52. int2_ths description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 table 53. int2_duration register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 table 54. int2_duration description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 table 55. tflga 3x3x1.0 mm 3 16l mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 table 56. document revision history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
list of figures H3LIS331DL 6/38 docid023111 rev 2 list of figures figure 1. block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 2. pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 3. spi slave timing diagram (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 figure 4. i 2 c slave timing diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 figure 5. H3LIS331DL electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 figure 6. read and write protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 7. spi read protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 8. multiple byte spi read protocol (2-byte example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 figure 9. spi write protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 figure 10. multiple byte spi write protocol (2-byte example). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 11. spi read protocol in 3-wire mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 12. tflga 3x3x1.0 mm 3 16l mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
docid023111 rev 2 7/38 H3LIS331DL block diagram and pin description 38 1 block diagram and pin description 1.1 block diagram figure 1. block diagram 1.2 pin description figure 2. pin connections charge amplifier y+ z+ y- z- a x+ x- i 2 c spi cs scl/spc sda/sdo/sdi sdo/sa0 control logic & interrupt gen. int 1 clock trimming circuits reference control logic a/d converter int 2 mux am12624v1 (top view) direction of the detectable accelerations 1 5 9 13 (bottom view) y 1 x z pin 1 indicator am12625v1
block diagram and pin description H3LIS331DL 8/38 docid023111 rev 2 table 2. pin description pin# name function 1 vdd_io power supply for i/o pins 2 nc not connected 3 nc not connected 4 scl spc i 2 c serial clock (scl) spi serial port clock (spc) 5 gnd 0 v supply 6 sda sdi sdo i 2 c serial data (sda) spi serial data input (sdi) 3-wire interface serial data output (sdo) 7 sdo sa0 spi serial data output (sdo) i 2 c less significant bit of the device address (sa0) 8cs spi enable i 2 c/spi mode selection (1: i 2 c mode; 0: spi enabled) 9 int 2 inertial interrupt 2 10 reserved connect to gnd 11 int 1 inertial interrupt 1 12 gnd 0 v supply 13 gnd 0 v supply 14 vdd power supply 15 reserved connect to vdd 16 gnd 0 v supply
docid023111 rev 2 9/38 H3LIS331DL mechanical and electrical specifications 38 2 mechanical and electrical specifications 2.1 mechanical characteristics @ vdd = 2.5 v, t = 25 c unless otherwise noted (a) . a. the product is factory calibrated at 2.5 v. the operational power supply range is from 2.16 v to 3.6 v. the product calibration is done at s 1 g . table 3. mechanical characteristics symbol parameter test conditions min. typ. (1) max. unit fs measurement range (2) fs bit set to 00 100 g fs bit set to 01 200 fs bit set to 11 400 so sensitivity (3) fs bit set to 00 12-bit representation 49 m g /digit fs bit set to 01 12-bit representation 98 fs bit set to 11 12-bit representation 195 tcso sensitivity change vs. temperature fs bit set to 00 0.01 %/c tyoff typical zero- g level offset accuracy (4) fs bit set to 00 1 g tcoff zero- g level change vs. temperature max. delta from 25 c 5 m g /c an acceleration noise density fs bit set to 00 15 m g / nl non-linearity fs bit set to 00 range -70g .. +70g 2 %fs top operating temperature range -40 +85 c wh product weight 20 mgram 1. typical specifications are not guaranteed. 2. verified by wafer level test and measurement of initial offset and sensitivity. 3. factory calibrated at s 1 g 4. offset can be eliminated by enabling the built-in high-pass filter. hz
mechanical and electrical specifications H3LIS331DL 10/38 docid023111 rev 2 2.2 electrical characteristics @ vdd = 2.5 v, t = 25 c unless otherwise noted (b) . b. the product is factory calibrated at 2.5 v. the operational power supply range is from 2.16 v to 3.6 v. table 4. electrical characteristics symbol parameter test conditions min. typ. (1) max. unit vdd supply voltage 2.16 2.5 3.6 v vdd_io i/o pins supply voltage (2) 1.71 vdd+0.1 v idd current consumption in normal mode 300 a iddlp current consumption in low- power mode 10 a iddpdn current consumption in power-down mode 1 a vih digital high-level input voltage 0.8*vdd_io v vil digital low-level input voltage 0.2*vdd_io v voh high-level output voltage 0.9*vdd_io v vol low-level output voltage 0.1*vdd_io v odr output data rate in normal mode dr bit set to 00 50 hz dr bit set to 01 100 dr bit set to 10 400 dr bit set to 11 1000 odr lp output data rate in low-power mode pm bit set to 010 0.5 hz pm bit set to 011 1 pm bit set to 100 2 pm bit set to 101 5 pm bit set to 110 10 bw system bandwidth (3) odr/2 hz ton turn-on time (4) odr = 100 hz 1/odr+1ms s top operating temperature range -40 +85 c 1. typical specifications are not guaranteed. 2. it is possible to remove vdd maintaining vdd_io without blocking the communication busses; in this condition the measurement chain is powered off. 3. refer to table 20 for filter cutoff frequency. 4. time to obtain valid data after exiting power-down mode.
docid023111 rev 2 11/38 H3LIS331DL mechanical and electrical specifications 38 2.3 communication interface characteristics 2.3.1 spi - serial peripheral interface subject to general operating conditions for vdd and top. figure 3. spi slave timing diagram (2) 2. measurement points are done at 0.2vdd_io and 0.8vdd_io, for both input and output ports. 3. when no communication is ongoing, data on cs, spc, sdi and sdo are driven by internal pull-up resistors. table 5. spi slave timing values symbol parameter value (1) unit min. max. t c(spc) spi clock cycle 100 ns f c(spc) spi clock frequency 10 mhz t su(cs) cs setup time 6 ns t h(cs) cs hold time 8 t su(si) sdi input setup time 5 t h(si) sdi input hold time 15 t v(so) sdo valid output time 50 t h(so) sdo output hold time 9 t dis(so) sdo output disable time 50 1. values are guaranteed at 10 mhz clock frequency for spi with both 4 and 3 wires, based on characterization results, not tested in production.
mechanical and electrical specifications H3LIS331DL 12/38 docid023111 rev 2 2.3.2 i 2 c - inter-ic control interface subject to general operating conditions for vdd and top. figure 4. i 2 c slave timing diagram note: measurement points are done at 0.2vdd_io and 0.8vdd_io, for both ports. table 6. i 2 c slave timing values symbol parameter i 2 c standard mode (1) i 2 c fast mode (1) unit min. max. min. max. f (scl) scl clock frequency 0 100 0 400 khz t w(scll) scl clock low time 4.7 1.3 s t w(sclh) scl clock high time 4.0 0.6 t su(sda) sda setup time 250 100 ns t h(sda) sda data hold time 0.01 3.45 0.01 0.9 s t r(sda) t r(scl) sda and scl rise time 1000 20 + 0.1c b (2) 300 ns t f(sda) t f(scl) sda and scl fall time 300 20 + 0.1c b ( 2) 300 t h(st) start condition hold time 4 0.6 s t su(sr) repeated start condition setup time 4.7 0.6 t su(sp) stop condition setup time 4 0.6 t w(sp:sr) bus free time between stop and start condition 4.7 1.3 1. data based on standard i 2 c protocol requirement, not tested in production. 2. c b = total capacitance of one bus line, in pf. sd a scl t f ( sd a ) t su ( sp) t w( scll) t su ( sd a ) t r( sd a ) t su ( sr) t h( st) t w( sclh ) t h( sd a ) t r( scl) t f ( sc l) t w( sp: sr) start repeated sta rt sto p sta rt
docid023111 rev 2 13/38 H3LIS331DL mechanical and electrical specifications 38 2.4 absolute maximum ratings stresses above those listed as ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device under these conditions is not implied. exposure to maximum rating conditions for extended periods may affect device reliability. note: supply voltage on any pin should never exceed 4.8 v. table 7. absolute maximum ratings symbol ratings maximum value unit vdd supply voltage -0.3 to 4.8 v vdd_io i/o pins supply voltage -0.3 to 4.8 v vin input voltage on any control pin (cs, scl/spc, sda/sdi/sdo, sdo/sa0) -0.3 to vdd_io +0.3 v a pow acceleration (any axis, powered, vdd = 2.5 v) 3000 g for 0.5 ms 10000 g for 0.1 ms a unp acceleration (any axis, unpowered) 3000 g for 0.5 ms 10000 g for 0.1 ms t op operating temperature range -40 to +85 c t stg storage temperature range -40 to +125 c esd electrostatic discharge protection 4 (hbm) kv 1.5 (cdm) kv 200 (mm) v this device is sensitive to mechanical shock, improper handling can cause permanent damage to the part. this is an electrostatic-sensitive device (esd), improper handling can cause permanent damage to the part.
mechanical and electrical specifications H3LIS331DL 14/38 docid023111 rev 2 2.5 terminology 2.5.1 sensitivity sensitivity describes the gain of the sensor and can be determined by applying 1 g acceleration to it. as the sensor can measure dc accelerations this can be done easily by pointing the axis of interest towards the center of the earth, noting the output value, rotating the sensor by 180 degrees (pointing to the sky) and noting the output value again. by doing so, 1 g acceleration is applied to the sensor. subtracting the larger output value from the smaller one, and dividing the result by 2, leads to the actual sensitivity of the sensor. this value changes very little over temperature and time. the sensitivity tolerance describes the range of sensitivities of a large population of sensors. 2.5.2 zero- g level the zero- g level offset (tyoff) describes the deviation of an actual output signal from the ideal output signal if no acceleration is present. a sensor in a steady-state on a horizontal surface measures 0 g for the x-axis and 0 g for the y-axis whereas the z-axis measures 1 g . the output is ideally in the middle of the dynamic range of the sensor (content of out registers 00h, data expressed as two?s complement number). a deviation from the ideal value in this case is called zero- g offset. offset is, to some extent, a result of stress to the mems sensor and therefore can slightly change after mounting the sensor onto a printed circuit board or exposing it to extensive mechanical stress. offset changes little over temperature, refer to ?zero- g level change vs. temperature? (see tcoff in table 3 ). the zero- g level tolerance (tyoff) describes the standard deviation of the range of zero- g levels of a population of sensors. 2.5.3 sleep-to-wakeup the ?sleep-to-wakeup? function, in conjunction with low-power mode, allows to further reduce the system power consumption and develop new smart applications. the H3LIS331DL may be set in a low-power operating mode, characterized by lower date rate refreshments. in this way the device, even if sleeping, continues to sense acceleration and generate interrupt requests. when the ?sleep-to-wakeup? function is activated, the H3LIS331DL is able to automatically wake up as soon as the interrupt event has been detected, increasing the output data rate and bandwidth. with this feature the system may be efficiently switched from low-power mode to full performance, depending on user-selectable positioning and acceleration events, therefore ensuring power saving and flexibility.
docid023111 rev 2 15/38 H3LIS331DL functionality 38 3 functionality the H3LIS331DL is a ?nano?, low-power, digital output 3-axis linear accelerometer housed in an lga package. the complete device includes a sensing element and an ic interface able to take the information from the sensing element and to provide a signal to the external world through an i 2 c/spi serial interface. 3.1 sensing element a proprietary process is used to create a surface micromachined accelerometer. the technology allows processing suspended silicon structures, which are attached to the substrate in a few points called anchors and are free to move in the direction of the sensed acceleration. to be compatible with traditional packaging techniques, a cap is placed on top of the sensing element to avoid blocking the moving parts during the molding phase of the plastic encapsulation. when an acceleration is applied to the sensor, the proof mass displaces from its nominal position, causing an imbalance in the capacitive half bridge. this imbalance is measured using charge integration in response to a voltage pulse applied to the capacitor. at steady-state the nominal value of the capacitors are a few pf and when an acceleration is applied, the maximum variation of the capacitive load is in the ff range. 3.2 ic interface the complete measurement chain is composed of a low-noise capacitive amplifier which converts the capacitive unbalancing of the mems sensor into an analog voltage that will be available to the user through an analog-to-digital converter. the acceleration data may be accessed through an i 2 c/spi interface, making the device particularly suitable for direct interfacing with a microcontroller. the H3LIS331DL features a data-ready signal (rdy) which indicates when a new set of measured acceleration data is available, therefore simplifying data synchronization in the digital system that uses the device. 3.3 factory calibration the ic interface is factory calibrated for sensitivity (so) and zero- g level (tyoff). the trim values are stored inside the device in non-volatile memory. any time the device is turned on, the trim parameters are downloaded into the registers to be used during active operation. this allows the device to be used without further calibration.
application hints H3LIS331DL 16/38 docid023111 rev 2 4 application hints figure 5. H3LIS331DL electrical connections the device core is supplied through the vdd line while the i/o pads are supplied through the vdd_io line. power supply decoupling capacitors (100 nf ceramic, 10 f aluminum) should be placed as near as possible to pin 14 of the device (common design practice). all the voltage and ground supplies must be present at the same time to have proper behavior of the ic (refer to figure 5 ). it is possible to remove vdd maintaining vdd_io without blocking the communication bus, in this condition the measurement chain is powered off. the functionality of the device and the measured acceleration data are selectable and accessible through the i 2 c or spi interfaces. when using the i 2 c, cs must be tied high. the functions, the threshold and the timing of the two interrupt pins (int 1 and int 2) can be completely programmed by the user through the i 2 c/spi interface. 4.1 soldering information the lga package is compliant with the ecopack ? , rohs and ?green? standards. it is qualified for soldering heat resistance according to jedec j-std-020c. leave ?pin 1 indicator? unconnected during soldering. land pattern and soldering recommendations are available at www .st.com . cs 10f vdd 100nf gnd vdd_io sdo/sa0 sda/sdi/sdo int 1 scl/spc digital signal from/to signal controller. signal levels are defined by proper selection of vdd_io 1 5 8 13 top view 6 9 14 16 9 5 int 2 am12626v1
docid023111 rev 2 17/38 H3LIS331DL digital interfaces 38 5 digital interfaces the registers embedded inside the H3LIS331DL may be accessed through both the i 2 c and spi serial interfaces. the latter may be sw configured to operate either in 3-wire or 4-wire interface mode. the serial interfaces are mapped onto the same pads. to select/exploit the i 2 c interface, the cs line must be tied high (i.e. connected to vdd_io). 5.1 i 2 c serial interface the H3LIS331DL i 2 c is a bus slave. the i 2 c is employed to write data into registers whose content can also be read back. the relevant i 2 c terminology is given in the table below. there are two signals associated with the i 2 c bus: the serial clock line (scl) and the serial data line (sda). the latter is a bi-directional line used for sending and receiving the data to/from the interface. both the lines are connected to vdd_io through a pull-up resistor embedded inside the H3LIS331DL. when the bus is free both lines are high. the i 2 c interface is compliant with fast mode (400 khz) i 2 c standards as well as with normal mode. table 8. serial interface pin description pin name pin description cs spi enable i 2 c/spi mode selection (1: i 2 c mode; 0: spi enabled) scl spc i 2 c serial clock (scl) spi serial port clock (spc) sda sdi sdo i 2 c serial data (sda) spi serial data input (sdi) 3-wire interface serial data output (sdo) sa0 sdo i 2 c less significant bit of the device address (sa0) spi serial data output (sdo) table 9. serial interface pin description term description transmitter the device which sends data to the bus receiver the device which receives data from the bus master the device which initiates a transfer, generates clock signals and terminates a transfer slave the device addressed by the master
digital interfaces H3LIS331DL 18/38 docid023111 rev 2 5.1.1 i 2 c operation the transaction on the bus is started through a start (st) signal. a start condition is defined as a high-to-low transition on the data line while the scl line is held high. after this has been transmitted by the master, the bus is considered busy. the next byte of data transmitted after the start condition contains the address of the slave in the first 7 bits and the eighth bit tells whether the master is receiving data from the slave or transmitting data to the slave. when an address is sent, each device in the system compares the first seven bits after a start condition with its address. if they match, the device considers itself addressed by the master. the slave address (sad) associated to the H3LIS331DL is 001100xb. the sdo / sa0 pad can be used to modify the less significant bit of the device address. if the sa0 pad is connected to the voltage supply, lsb is ?1? (address 0011001b) or else, if the sa0 pad is connected to ground, the lsb value is ?0? (address 0011000b). this solution allows the connection and addressing of two different accelerometers to the same i 2 c lines. data transfer with acknowledge is mandatory. the transmitter must release the sda line during the acknowledge pulse. the receiver must then pull the data line low so that it remains stable low during the high period of the acknowledge clock pulse. a receiver which has been addressed is obliged to generate an acknowledge after each byte of data received. the i 2 c embedded inside the H3LIS331DL behaves like a slave device and the following protocol must be adhered to. after the start condition (st) a slave address is sent, once a slave acknowledge (sak) has been returned, an 8-bit sub-address (sub) is transmitted: the 7 lsb represent the actual register address while the msb enables address auto increment. if the msb of the sub field is ?1?, the sub (register address) is automatically increased to allow multiple data read/write. the slave address is completed with a read/write bit. if the bit is ?1? (read), a repeated start (sr) condition must be issued after the two sub-address bytes; if the bit is ?0? (write), the master transmits to the slave with the direction unchanged. table 10 explains how the sad+read/write bit pattern is composed, listing all the possible configurations. table 10. sad+read/write patterns command sad[6:1] sad[0] = sa0 r/w sad+r/w read 001100 0 1 00110001 (31h) write 001100 0 0 00110000 (30h) read 001100 1 1 00110011 (33h) write 001100 1 0 00110010 (32h) table 11. transfer when master is writing one byte to slave master st sad + w sub data sp slave sak sak sak
docid023111 rev 2 19/38 H3LIS331DL digital interfaces 38 data are transmitted in byte format (data). each data transfer contains 8 bits. the number of bytes transferred per transfer is unlimited. data is transferred with the most significant bit (msb) first. if a receiver can?t receive another complete byte of data until it has performed some other function, it can hold the clock line scl low to force the transmitter into a wait state. data transfer only continues when the receiver is ready for another byte and releases the data line. if a slave receiver doesn?t acknowledge the slave address (i.e. it is not able to receive because it is performing some real-time function) the data line must be left high by the slave. the master can then abort the transfer. a low-to-high transition on the sda line while the scl line is high is defined as a stop condition. each data transfer must be terminated by the generation of a stop (sp) condition. in order to read multiple bytes, it is necessary to assert the most significant bit of the sub- address field. in other words, sub(7) must be equal to 1 while sub(6-0) represents the address of first register to be read. in the presented communication format mak is master acknowledge and nmak is no master acknowledge. 5.2 spi bus interface the H3LIS331DL spi is a bus slave. the spi allows the writing and reading of the device registers. the serial interface interacts with the outside world with 4 wires: cs , spc , sdi and sdo . table 12. transfer when master is writing multiple bytes to slave master st sad + w sub data data sp slave sak sak sak sak table 13. transfer when master is receiving (reading) one byte of data from slave master st sad + w sub sr sad + r nmak sp slave sak sak sak data table 14. transfer when master is receiving (reading) multiple bytes of data from slave master st sad+w sub sr sad+r mak mak nmak sp slave sak sak sak data dat a dat a
digital interfaces H3LIS331DL 20/38 docid023111 rev 2 figure 6. read and write protocol cs is the serial port enable and it is controlled by the spi master. it goes low at the start of the transmission and goes back high at the end. spc is the serial port clock and it is controlled by the spi master. it is stopped high when cs is high (no transmission). sdi and sdo are respectively the serial port data input and output. those lines are driven at the falling edge of spc and should be captured at the rising edge of spc . both the read register and write register commands are completed in 16 clock pulses or in multiples of 8 in the case of multiple read/write bytes. bit duration is the time between two falling edges of spc . the first bit (bit 0) starts at the first falling edge of spc after the falling edge of cs while the last bit (bit 15, bit 23, ...) starts at the last falling edge of spc just before the rising edge of cs . bit 0 : r w bit. when 0, the data di(7:0) is written into the device. when 1, the data do(7:0) from the device is read. in the latter case, the chip drives sdo at the start of bit 8. bit 1 : m s bit. when 0, the address remains unchanged in multiple read/write commands. when 1, the address is auto-incremented in multiple read/write commands. bit 2-7 : address ad(5:0). this is the address field of the indexed register. bit 8-15 : data di(7:0) (write mode). this is the data that is written into the device (msb first). bit 8-15 : data do(7:0) (read mode). this is the data that is read from the device (msb first). in multiple read/write commands further blocks of 8 clock periods are added. when the m s bit is ?0?, the address used to read/write data remains the same for every block. when the m s bit is ?1? the address used to read/write data is increased at every block. the function and the behavior of sdi and sdo remain unchanged. 5.2.1 spi read figure 7. spi read protocol cs spc sdi sdo rw ad5 ad4 ad3 ad2 ad1 ad0 di7 di6 di5 di4 di3 di2 di1 di0 do7 do6 do5 do4 do3 do2 do1 do0 ms cs spc sdi sdo rw do7 do6 do5 do4 do3 do2 do1 do0 ad5 ad4 ad3 ad2 ad1 ad0 ms
docid023111 rev 2 21/38 H3LIS331DL digital interfaces 38 the spi read command is performed with 16 clock pulses. a multiple byte read command is performed by adding blocks of 8 clock pulses to the previous one. bit 0 : read bit. the value is 1. bit 1 : m s bit. when 0, does not increment the address. when 1, increments the address in multiple reads. bit 2-7 : address ad(5:0). this is the address field of the indexed register. bit 8-15 : data do(7:0) (read mode). this is the data that is read from the device (msb first). bit 16-... : data do(...-8). further data in multiple byte reads. figure 8. multiple byte spi read protocol (2-byte example) 5.2.2 spi write figure 9. spi write protocol the spi write command is performed with 16 clock pulses. a multiple byte write command is performed by adding blocks of 8 clock pulses to the previous one. bit 0 : write bit. the value is 0. bit 1 : m s bit. when 0, does not increment the address. when 1, increments the address in multiple writes. bit 2 -7 : address ad(5:0). this is the address field of the indexed register. bit 8-15 : data di(7:0) (write mode). this is the data that is written inside the device (msb first). bit 16-... : data di(...-8). further data in multiple byte writes. cs spc sdi sdo rw do7 do6 do5 do4 do3 do2 do1 do0 ad5 ad4 ad3 ad2 ad1 ad0 do15 do14 do13 do12 do11 do10 do9 do8 ms cs spc sdi rw di7 di6 di5 di4 di3 di2 di1 di0 ad5 ad4 ad3 ad2 ad1 ad0 ms
digital interfaces H3LIS331DL 22/38 docid023111 rev 2 figure 10. multiple byte spi write protocol (2-byte example) 5.2.3 spi read in 3-wire mode 3-wire mode is entered by setting bit sim (spi serial interface mode selection) to ?1? in ctrl_reg4. figure 11. spi read protocol in 3-wire mode the spi read command is performed with 16 clock pulses: bit 0 : read bit. the value is 1. bit 1 : m s bit. when 0, does not increment the address. when 1, increments the address in multiple reads. bit 2-7 : address ad(5:0). this is the address field of the indexed register. bit 8-15 : data do(7:0) (read mode). this is the data that is read from the device (msb first). the multiple read command is also available in 3-wire mode. cs spc sdi rw ad5 ad4 ad3 ad2 ad1 ad0 di7 di6 di5 di4 di3 di2 di1 di0 di15 di14 di13 di12 di11 di10 di9 di8 ms cs spc sdi/o rw do7 do6 do5 do4 do3 do2 do1 do0 ad5 ad4 ad3 ad2 ad1 ad0 ms
docid023111 rev 2 23/38 H3LIS331DL register mapping 38 6 register mapping table 15 provides a listing of the 8-bit registers embedded in the device and the related addresses. registers marked as reserved must not be changed as they contain the factory calibration values. their content is automatically restored when the device is powered up. writing to those registers may change calibration data and thus lead to improper functioning of the device. table 15. register address map name type register address default comment hex binary reserved (do not modify) 00 - 0e reserved who_am_i r 0f 000 1111 00110010 dummy register reserved (do not modify) 10 - 1f reserved ctrl_reg1 rw 20 010 0000 00000111 ctrl_reg2 rw 21 010 0001 00000000 ctrl_reg3 rw 22 010 0010 00000000 ctrl_reg4 rw 23 010 0011 00000000 ctrl_reg5 rw 24 010 0100 00000000 hp_filter_reset r 25 010 0101 dummy register reference rw 26 010 0110 00000000 status_reg r 27 010 0111 00000000 out_x_l r 28 010 1000 output out_x_h r 29 010 1001 output out_y_l r 2a 010 1010 output out_y_h r 2b 010 1011 output out_z_l r 2c 010 1100 output out_z_h r 2d 010 1101 output reserved (do not modify) 2e - 2f reserved int1_cfg rw 30 011 0000 00000000 int1_src r 31 011 0001 00000000 int1_ths rw 32 011 0010 00000000 int1_duration rw 33 011 0011 00000000 int2_cfg rw 34 011 0100 00000000 int2_src r 35 011 0101 00000000 int2_ths rw 36 011 0110 00000000 int2_duration rw 37 011 0111 00000000 reserved (do not modify) 38 - 3f reserved
register description H3LIS331DL 24/38 docid023111 rev 2 7 register description the device contains a set of registers which are used to control its behavior and to retrieve acceleration data. the register address, consisting of 7 bits, is used to identify them and to write the data through the serial interface. 7.1 who_am_i (0fh) device identification register. this register contains the device identifier that for the H3LIS331DL is set to 32h. 7.2 ctrl_reg1 (20h) the pm bits allow the user to select between power-down and two operating active modes. the device is in power-down mode when the pd bits are set to ?000? (default value after boot). table 19 shows all the possible power mode configurations and respective output data rates. output data in the low-power mode are computed with the low-pass filter cutoff frequency defined by the dr1, dr0 bits. the dr bits, in normal mode operation, select the data rate at which acceleration samples are produced. in low-power modes they define the output data resolution. table 20 shows all the possible configurations for the dr1 and dr0 bits. table 16. who_am_i register 00110010 table 17. ctrl_reg1 register pm2 pm1 pm0 dr1 dr0 zen yen xen table 18. ctrl_reg1 description pm2 - pm0 power mode selection. default value: 000 (000: power-down; others: refer to table 19 ) dr1, dr0 data rate selection. default value: 00 (00:50 hz; others: refer to table 20 ) zen z-axis enable. default value: 1 (0: z-axis disabled; 1: z-axis enabled) yen y-axis enable. default value: 1 (0: y-axis disabled; 1: y-axis enabled) xen x-axis enable. default value: 1 (0: x-axis disabled; 1: x-axis enabled)
docid023111 rev 2 25/38 H3LIS331DL register description 38 7.3 ctrl_reg2 (21h) table 19. power mode and low-power output data rate configurations pm2 pm1 pm0 power mode selection output data rate [hz] odr lp 0 0 0 power-down -- 0 0 1 normal mode odr 0 1 0 low power 0.5 0 1 1 low power 1 1 0 0 low power 2 1 0 1 low power 5 1 1 0 low power 10 table 20. normal mode output data rate configurations and low-pass cutoff frequencies dr1 dr0 output data rate [hz] odr low-pass filter cutoff frequency [hz] 0 0 50 37 0 1 100 74 1 0 400 292 1 1 1000 780 table 21. ctrl_reg2 register boot hpm1 hpm0 fds hpen2 hpen1 hpcf1 hpcf0 table 22. ctrl_reg2 description boot reboot memory content. default value: 0 (0: normal mode; 1: reboot memory content) hpm1, hpm0 high-pass filter mode selection. default value: 00 (00: normal mode; others: refer to table 23 ) fds filtered data selection. default value: 0 (0: internal filter bypassed; 1: data from internal filter sent to output register) hpen2 high-pass filter enabled for interrupt 2 source. default value: 0 (0: filter bypassed; 1: filter enabled)
register description H3LIS331DL 26/38 docid023111 rev 2 the boot bit is used to refresh the content of the internal registers stored in the flash memory block. at device power-up, the content of the flash memory block is transferred to the internal registers related to trimming functions in order to permit correct operation of the device itself. if for any reason the content of the trimming registers is changed, it is sufficient to use this bit to restore the correct values. when the boot bit is set to ?1?, the content of the internal flash is copied inside the corresponding internal registers and it is used to calibrate the device. these values are factory trimmed and they are different for every accelerometer. they permit correct operation of the device and normally they do not have to be changed. at the end of the boot process the boot bit is set again to ?0?. hpcf[1:0] . these bits are used to configure the high-pass filter cutoff frequency f t which is given by: the equation can be simplified to the following approximated equation: hpen1 high-pass filter enabled for interrupt 1 source. default value: 0 (0: filter bypassed; 1: filter enabled) hpcf1, hpcf0 high-pass filter cutoff frequency configuration. default value: 00 (00: hpc=8; 01: hpc=16; 10: hpc=32; 11: hpc=64) table 23. high-pass filter mode configuration hpm1 hpm0 high-pass filter mode 00 normal mode (reset reading hp_reset_filter) 01 reference signal for filtering 10 normal mode (reset reading hp_reset_filter) table 24. high-pass filter cutoff frequency configuration hpcoeff2,1 f t [hz] data rate = 50 hz f t [hz] data rate = 100 hz f t [hz] data rate = 400 hz f t [hz] data rate = 1000 hz 00 1 2 8 20 01 0.5 1 4 10 10 0.25 0.5 2 5 11 0.125 0.25 1 2.5 table 22. ctrl_reg2 description (continued) f t 1 1 hpc ----------- - ? ?? ?? f s 2 ? ------ ? ln = f t f s 6hpc ? ------------------- =
docid023111 rev 2 27/38 H3LIS331DL register description 38 7.4 ctrl_reg3 [interrupt ctrl register] (22h) 7.5 ctrl_reg4 (23h) table 25. ctrl_reg3 register ihl pp_od lir2 i2_cfg1 i2_cfg0 lir1 i1_cfg1 i1_cfg0 table 26. ctrl_reg3 description ihl interrupt active high, low. default value: 0 (0: active high; 1: active low) pp_od push-pull/open drain selection on interrupt pad. default value 0. (0: push-pull; 1: open drain) lir2 latch interrupt request on int2_src register, with int2_src register cleared by reading int2_src itself. default value: 0. (0: interrupt request not latched; 1: interrupt request latched) i2_cfg1, i2_cfg0 data signal on int 2 pad control bits. default value: 00. (see table 27 ) lir1 latch interrupt request on the int1_src register, with the int1_src register cleared by reading the int1_src register. default value: 0. (0: interrupt request not latched; 1: interrupt request latched) i1_cfg1, i1_cfg0 data signal on int 1 pad control bits. default value: 00. (see table 27 ) table 27. data signal on int 1 and int 2 pad i1(2)_cfg1 i1(2)_cfg0 int 1(2) pad 0 0 interrupt 1 (2) source 0 1 interrupt 1 source or interrupt 2 source 1 0 data ready 1 1 boot running table 28. ctrl_reg4 register bdu ble fs1 fs0 0 0 0 sim
register description H3LIS331DL 28/38 docid023111 rev 2 the bdu bit is used to inhibit output register updates between the reading of upper and lower register parts. in default mode (bdu = ?0?), the lower and upper register parts are updated continuously. when the bdu is activated (bdu = ?1?), the content of the output registers is not updated until both msb and lsb are read which avoids reading values related to different sample times. 7.6 ctrl_reg5 (24h) turn-on bits are used for turning on the sleep-to-wake function. setting turnon[1:0] bits to 11, the ?sleep-to-wake? function is enabled. when an interrupt event occurs, the device is turned to normal mode, increasing the odr to the value defined in ctrl_reg1. although the device is in normal mode, ctrl_reg1 content is not automatically changed to ?normal mode? configuration. table 29. ctrl_reg4 description bdu block data update. default value: 0 (0: continuous update; 1: output registers not updated between msb and lsb reading) ble big/little endian data selection. default value 0. (0: data lsb @ lower address; 1: data msb @ lower address) fs1, fs0 full scale selection. default value: 00. (00: 100 g ; 01: 200 g ; 11: 400 g ) sim spi serial interface mode selection. default value: 0. (0: 4-wire interface; 1: 3-wire interface) table 30. ctrl_reg5 register 0 0 0 0 0 0 turnon1 turnon0 table 31. ctrl_reg5 description turnon1, turnon0 turn-on mode selection for sleep-to-wake function. default value: 00. table 32. sleep-to-wake configuration turnon1 turnon0 sleep-to-wake status 0 0 sleep-to-wake function is disabled 11 turned on: the device is in low-power mode (odr is defined in ctrl_reg1)
docid023111 rev 2 29/38 H3LIS331DL register description 38 7.7 hp_filter_reset (25h) dummy register. reading at this address zeroes instantaneously the content of the internal high-pass filter. if the high-pass filter is enabled, all three axes are instantaneously set to 0 g. this allows the settling time of the high-pass filter to be overcome. 7.8 reference (26h) this register sets the acceleration value taken as a reference for the high-pass filter output. when the filter is turned on (at least one of the fds, hpen2, or hpen1 bits is equal to ?1?) and the hpm bits are set to ?01?, filter-out is generated, taking this value as a reference. 7.9 status_reg (27h) table 33. reference register ref7 ref6 ref5 ref4 ref3 ref2 ref1 ref0 table 34. reference description ref7 - ref0 reference value for high-pass filter. default value: 00h. table 35. status_reg register zyxor zor yor xor zyxda zda yda xda table 36. status_reg description zyxor x, y and z-axis data overrun. default value: 0 (0: no overrun has occurred; 1: new data has overwritten the previous data before it was read) zor z-axis data overrun. default value: 0 (0: no overrun has occurred; 1: new data for the z-axis has overwritten the previous data) yor y-axis data overrun. default value: 0 (0: no overrun has occurred; 1: new data for the y-axis has overwritten the previous data) xor x-axis data overrun. default value: 0 (0: no overrun has occurred; 1: new data for the x-axis has overwritten the previous data) zyxda x, y and z-axis new data available. default value: 0 (0: a new set of data is not yet available; 1: a new set of data is available)
register description H3LIS331DL 30/38 docid023111 rev 2 7.10 out_x_l (28h), out_x_h (29h) x-axis acceleration data. the value is expressed as two?s complement. 7.11 out_y_l (2ah), out_y_h (2bh) y-axis acceleration data. the value is expressed as two?s complement. 7.12 out_z_l (2ch), out_z_h (2dh) z-axis acceleration data. the value is expressed as two?s complement. 7.13 int1_cfg (30h) zda z-axis new data available. default value: 0 (0: new data for the z-axis is not yet available; 1: new data for the z-axis is available) yda y-axis new data available. default value: 0 (0: new data for the y-axis is not yet available; 1: new data for the y-axis is available) xda x-axis new data available. default value: 0 (0: new data for the x-axis is not yet available; 1: new data for the x-axis is available) table 36. status_reg description (continued) table 37. int1_cfg register aoi 0 zhie zlie yhie ylie xhie xlie table 38. int1_cfg description aoi and/or combination of interrupt events. default value: 0. (see table 39 ) zhie enable interrupt generation on z high event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value higher than preset threshold) zlie enable interrupt generation on z low event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value lower than preset threshold) yhie enable interrupt generation on y high event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value higher than preset threshold) ylie enable interrupt generation on y low event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value lower than preset threshold)
docid023111 rev 2 31/38 H3LIS331DL register description 38 configuration register for interrupt 1 source. 7.14 int1_src (31h) interrupt 1 source register. read-only register. reading at this address clears the int1_src ia bit (and the interrupt signal on the int 1 pin) and allows the refreshment of data in the int1_src register if the latched option is chosen. xhie enable interrupt generation on x high event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value higher than preset threshold) xlie enable interrupt generation on x low event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value lower than preset threshold) table 39. interrupt 1 source configurations aoi interrupt mode 0 or combination of interrupt events 1 and combination of interrupt events table 38. int1_cfg description (continued) table 40. int1_src register 0 ia zhzlyhylxhxl table 41. int1_src description ia interrupt active. default value: 0 (0: no interrupt has been generated; 1: one or more interrupts have been generated) zh z high. default value: 0 (0: no interrupt, 1: z high event has occurred) zl z low. default value: 0 (0: no interrupt; 1: z low event has occurred) yh y high. default value: 0 (0: no interrupt, 1: y high event has occurred) yl y low. default value: 0 (0: no interrupt, 1: y low event has occurred) xh x high. default value: 0 (0: no interrupt, 1: x high event has occurred) xl x low. default value: 0 (0: no interrupt, 1: x low event has occurred)
register description H3LIS331DL 32/38 docid023111 rev 2 7.15 int1_ths (32h) 7.16 int1_duration (33h) the d6 - d0 bits set the minimum duration of the interrupt 2 event to be recognized. duration steps and maximum values depend on the odr chosen. 7.17 int2_cfg (34h) table 42. int1_ths register 0 ths6 ths5 ths4 ths3 ths2 ths1 ths0 table 43. int1_ths description ths6 - ths0 interrupt 1 threshold. default value: 000 0000 table 44. int1_duration register 0 d6d5d4d3d2d1d0 table 45. int2_duration description d6 - d0 duration value. default value: 000 0000 table 46. int2_cfg register aoi 0 zhie zlie yhie ylie xhie xlie table 47. int2_cfg description aoi and/or combination of interrupt events. default value: 0. (see table 48 ) zhie enable interrupt generation on z high event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value higher than preset threshold) zlie enable interrupt generation on z low event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value lower than preset threshold) yhie enable interrupt generation on y high event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value higher than preset threshold) ylie enable interrupt generation on y low event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value lower than preset threshold)
docid023111 rev 2 33/38 H3LIS331DL register description 38 configuration register for interrupt 2 source. 7.18 int2_src (35h) interrupt 2 source register. read-only register. reading at this address clears the int2_src ia bit (and the interrupt signal on the int 2 pin) and allows the refreshment of data in the int2_src register if the latched option is chosen. xhie enable interrupt generation on x high event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value higher than preset threshold) xlie enable interrupt generation on x low event. default value: 0 (0: disable interrupt request; 1: enable interrupt request on measured accel. value lower than preset threshold) table 48. interrupt mode configuration aoi interrupt mode 0 or combination of interrupt events 1 and combination of interrupt events table 47. int2_cfg description (continued) table 49. int2_src register 0 ia zhzlyhylxhxl table 50. int2_src description ia interrupt active. default value: 0 (0: no interrupt has been generated; 1: one or more interrupts have been generated) zh z high. default value: 0 (0: no interrupt, 1: z high event has occurred) zl z low. default value: 0 (0: no interrupt; 1: z low event has occurred) yh y high. default value: 0 (0: no interrupt, 1: y high event has occurred) yl y low. default value: 0 (0: no interrupt, 1: y low event has occurred) xh x high. default value: 0 (0: no interrupt, 1: x high event has occurred) xl x low. default value: 0 (0: no interrupt, 1: x low event has occurred)
register description H3LIS331DL 34/38 docid023111 rev 2 7.19 int2_ths (36h) 7.20 int2_duration (37h) the d6 - d0 bits set the minimum duration of the interrupt 2 event to be recognized. duration time steps and maximum values depend on the odr chosen. table 51. int2_ths register 0 ths6 ths5 ths4 ths3 ths2 ths1 ths0 table 52. int2_ths description ths6 - ths0 interrupt 1 threshold. default value: 000 0000 table 53. int2_duration register 0 d6d5d4d3d2d1d0 table 54. int2_duration description d6 - d0 duration value. default value: 000 0000
docid023111 rev 2 35/38 H3LIS331DL package information 38 8 package information in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack specifications, grade definitions and product status are available at: www.st.com. ecopack is an st trademark.
package information H3LIS331DL 36/38 docid023111 rev 2 figure 12. tflga 3x3x1.0 mm 3 16l mechanical drawing table 55. tflga 3x3x1.0 mm 3 16l mechanical data dim. mm min. typ. max. a1 1 a2 0.785 a3 0.200 d1 2.850 3.000 3.150 e1 2.850 3.000 3.150 l1 1.000 1.060 l2 2.000 2.060 n1 0.500 n2 1.000 m 0.040 0.100 0.160 p1 0.875 p2 1.275 t1 0.290 0.350 0.410 t2 0.190 0.250 0.310 d 0.150 k 0.050 7983231_l
docid023111 rev 2 37/38 H3LIS331DL revision history 38 9 revision history table 56. document revision history date revision changes 20-apr-2012 1 initial release 16-jul-2013 2 document status promoted from preliminary data to production data updated table 3 minor textual updates
H3LIS331DL 38/38 docid023111 rev 2 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. a ll st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not authorized for use in weapons. nor are st products designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, a utomotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2013 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of H3LIS331DL

	To Download H3LIS331DL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .